Application
Special characteristics
Parts and characteristics
Construction features
The expansion module EM-LON supplements the EASYLAB base components (controller TCU3 or adapter module TAM) with a LonWorks interface to link rooms or individual volume flow controllers to the central BMS.
The LonWorks interface supports the EASYLAB room operating mode concept. It is possible to set operating mode defaults in order to control different volume flow rates for daytime and night-time operation; it is also possible to increase or reduce the air change rate by a certain amount (volume flow rate setpoint change), e.g. to influence the room temperature.
Using the LonWorks interface, an individual alarm management system can be set up by consolidating configurable EASYLAB alarms. The interface also enables the transfer of actual operating values such as volume flow rates and damper blade position for a controller or for all controllers in a room.
Supply voltage | 5 V DC from controller or adapter module |
Communication interface | LonWorks-Transceiver FTT-10A, free topology, twisted pair |
Connection to LonWorks network | 6 terminals for cable cross sections of 0.12 – 1.5 mm² (LON A, LON B and screen, two of each) |
Operating temperature | 0 – 50 °C |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 20 |
EC conformity | EMC to 2004/108/EU, low voltage to 2006/95/EU |
Dimensions (B × H × T) | 78 × 65 × 100 mm |
Expansion module to supplement an EASYLAB base component (controller TCU3 or adapter module TAM) with a LonWorks interface to link rooms or individual volume flow controllers to the central BMS.
The expansion module includes a LonWorks transceiver FTT-10A (free topology, twisted pair), a service pin push button for LonWorks integration, and indicator lights for 'sending data' and 'receiving data'.
Special characteristics
Technical data
Data points for a single controller
Additional data points for a fume cupboard controller
Data points for an EASYLAB room
Single controller
Interface for one EASYLAB controller
Data points for a single controller
Additional data points for a fume cupboard controller
EASYLAB room
Interface for one EASYLAB room
Data points for an EASYLAB room controller
LonWorks interface
Description of network variables (SNVT)
All variables and parameters are based on standard network variables (SNVT); this ensures integration of the expansion module EM-LON into a LonWorks network.
The equipment functions that support each variable are listed under the special information for that network variable.
Abbreviations
Operating mode default setting
Operating modes Standard mode
Standard mode means normal operation in the daytime (in Germany: usually according to DIN 1946, part 7, 25 m³/h extract air per m² main useful floor area)
Reduced operation
Low mode in comparison to standard mode, e.g. as a night-time setback
Increased operation
High mode in comparison to standard mode, e.g. in an emergency
Shut-off mode
Shut-off of the volume flow controller, e.g. to save energy at night or to shut down the system
OPEN position
Open position of the volume flow controller
Overview of input variables for LonWorks interface EM-LON
nviManOverride | SNVT_hvac_overid | x¹ | x | x | Operating mode default setting for controller or room | |||
nviMode | SNVT_state | x¹ | x | x | Operating mode default setting for controller or room | |||
nviOccCmd | SNVT_occupancy | x¹ | x | x | Operating mode default setting for controller or room | |||
nviManOP_Disable | SNVT_switch | x¹ | x | x | Enabling/disabling manual control | |||
nviVolOffset_T | SNVT_switch | x | x | Signalling of a volume flow rate setpoint change for temperature control | ||||
nviVolOffset_P | SNVT_switch | x | x | Signalling of a volume flow rate setpoint change for differential pressure control | ||||
nviPressSetSel | SNVT_switch | x | x | Switching between differential pressure setpoint values 1 and 2 | ||||
nviSunblinder | SNVT_switch | x | x | Control input signal for sun protection/blinds | ||||
nviVolflowExh | SNVT_flow | x | x | x | x | x | Connection of an extract air flow | |
nviVolflowSup | SNVT_flow | x | x | x | x | x | Connection of a supply air flow | |
nviSC_LockHP | SNVT_switch | Close and lock sash, high priority | ||||||
nviSC_SetPos | SNVT_switch | Default setting from central BMS: Close sash | ||||||
nviDO_Set | SNVT_state | x | x | x | x | x | x | Signalling to relays which are not used by the control system |
nviVolflowSet_R | SNVT_flow | Default setting of volume flow rate setpoint (room), only for standard mode | ||||||
nviPressSet | SNVT_press_p | Local default setting of room pressure or duct pressure setpoint value | ||||||
nviVoltageAO2 | SNVT_volt | x | x | x | x | x | x | Default setting of voltage for output AO2 |
1 only for individually selected operating mode (stand-alone operation)
FH: Fume cupboard controller
RR: Room controller for supply air or extract air (RS, RE, PC)
RR RMF: Room controller with active room management function
EC, SC: Single controller for supply air or extract air (EC, SC)
TAM: Adapter module
TAM RMF: Adapter module with active room management function
Overview of output variables for LonWorks interface EM-LON
nvoManOverride | SNVT_hvac_overid | x | x | x | x | Operating mode for a single controller | ||
nvoManOverride_R | SNVT_hvac_overid | x | x | Operating mode for the room | ||||
nvoMode | SNVT_state | x | x | x | x | Operating mode for a single controller | ||
nvoMode_R | SNVT_state | x | x | Operating mode for the room | ||||
nvoOccCmd | SNVT_occupancy | x | x | x | x | Operating mode for a single controller | ||
nvoOccCmd_R | SNVT_occupancy | x | x | Operating mode for the room | ||||
nvoVolflowSet | SNVT_flow | x | x | x | x | Volume flow rate setpoint value for the controller | ||
nvoVolflowAct | SNVT_flow | x | x | x | x | Volume flow rate actual value for the controller | ||
nvoVolTotalExh | SNVT_flow | x | x | x | x | x | x | Total extract air for the room |
nvoVolTotalSup | SNVT_flow | x | x | x | x | x | x | Total supply air for the room |
nvoPressSet | SNVT_press_p | x | x | Differential pressure setpoint value for the room | ||||
nvoPressAct | SNVT_press_p | x | x | Differential pressure actual value for the room | ||||
nvoLocalAlarm | SNVT_switch | x | x | x | x | x | x | Alarm for the single controller |
nvoSummaryAlarm | SNVT_switch | x | x | Consolidated alarm for the room | ||||
nvoPressAlarm | SNVT_switch | x | x | Differential pressure alarm | ||||
nvoVelocitySet | SNVT_speed_mil | x | Face velocity actual value | |||||
nvoVelocityAct | SNVT_speed_mil | x | Face velocity setpoint value | |||||
nvoSwitchPos | SNVT_count | x | Sash position (stage 1,2,3) | |||||
nvoWireSensorPos | SNVT_switch | x | Sash position (sash opening %) | |||||
nvoDampPos | SNVT_switch | x | x | x | x | Damper blade position of single controller | ||
nvoSystemDevices | SNVT_count | x | x | x | x | x | x | Number of EASYLAB controllers |
nvoStateDIO | SNVT_state | x | x | x | x | x | x | State of the digital inputs and outputs (TCU3) |
nvoSC_LockHP | SNVT_switch | Feedback, sash has been locked, high priority | ||||||
nvoSC_GetPos | SNVT_switch | Signalling of position status | ||||||
nvoSC_Alarm | SNVT_switch | Signal for automatic sash device | ||||||
nvoDO_SetByLocal | SNVT_state | x | x | x | x | x | x | Indicates which relay is already being used by the controller |
nvoVoltageAI2 | SNVT_volt | x | x | x | x | x | x | Actual voltage at input AI2 |
nvoVoltageAI3 | SNVT_volt | x | x | x | x | x | x | Actual voltage at input AI3 |
nvoDampPosMax_FH | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position for fume cupboards – max |
nvoDampPosMin_FH | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position for fume cupboards – min |
nvoDampPosMax_RE | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position, extract air – max |
nvoDampPosMin_RE | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position, extract air – min |
nvoDampPosMax_TE | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position, total extract air – max |
nvoDampPosMin_TE | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position, total extract air – min |
nvoDampPosMax_RS | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position, supply air – max |
nvoDampPosMin_RS | SNVT_switch | x | x | x | x | x | x | Evaluated damper blade position, supply air – min |
nvoDampPosMax_EC | SNVT_switch | x | x | x | x | x | x | Output of the damper blade position of the extract air controller with the widest open damper blade |
nvoDampPosMin_EC | SNVT_switch | x | x | x | x | x | x | Output of the damper blade position of the extract air controller with the least wide open damper blade |
nvoDampPosMax_SC | SNVT_switch | x | x | x | x | x | x | Output of the damper blade position of the supply air controller with the widest open damper blade |
nvoDampPosMin_SC | SNVT_switch | x | x | x | x | x | x | Output of the damper blade position of the supply air controller with the least wide open damper blade |
nvoDampPosMax_TS | SNVT_switch | x | x | x | x | x | x | Output of the damper blade position of the supply air controller with the widest open damper blade |
nvoDampPosMin_TS | SNVT_switch | x | x | x | x | x | x | Output of the damper blade position of the supply air controller with the least wide open damper blade |
FH: Fume cupboard controller
RR: Room controller for supply air or extract air (RS, RE, PC)
RR RMF: Room controller with active room management function
EC, SC: Single controller for supply air or extract air (EC, SC)
TAM: Adapter module
TAM RMF: Adapter module with active room management function
Configuration parameter
nciConfig_Occ
Type: SCPTdirection
Equipment functions: FH, RR with RMF, TAM with RMF
Function
nciMaxSendTime
Type: SCPTmaxSndT
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
Input variables
nviManOverride
Type: SNVT_hvac_overid
Equipment functions: FH, RR with RMF, TAM with RMF
Function
nviOccCmd
Type: SNVT_occupancy
Equipment functions: FH, RR with RMF, TAM with RMF
Function
The assigment of functional values to operating modes is stored in the nciConfig_Occ table in the controller and can be configured
nviMode
Type: SNVT_state
Equipment functions: FH, RR with RMF, TAM with RMF
Function
nviManOp_Disable
Type: SNVT_switch
Equipment functions: FH, RR with RMF, TAM with RMF
Function
nviVolOffset_T
Type: SNVT_switch
Equipment functions: RR with RMF, TAM with RMF
Function
nviVolOffset_P
Type: SNVT_switch
Equipment functions: RR with RMF, TAM with RMF
Function
nviPressSetSel
Type: SNVT_switch
Equipment functions: RR with RMF, TAM with RMF
Function
nviSunblinder
Type: SNVT_switch
Equipment functions: RR with RMF, TAM with RMF
from firmware version EM-LON 2.0 and TCU3, TAM 3.0
Function
nviVolflowExh
Type: SNVT_flow, unit l/s
Equipment functions: FH, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 2.0 and TCU3, TAM 3.0
Function
nviVolflowSup
Type: SNVT_flow, unit l/s
Equipment functions: FH, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 2.0 and TCU3, TAM 3.0
Function
nviSC_LockHP
Type: SNVT_switch
Function
nviSC_SetPos
Type: SNVT_switch
Function
nviDO_Set
Type: SNVT_State
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 5.0
Function
nviVolflowSet_R
Typ: SNVT_flow
Function
nviPressSet
Typ: SNVT_flow
Function
nviVoltageAO2
Type: SNVT_volt, unit V
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 4.0 and TCU3, TAM 7.0
Function
Output variables
nvoManOverride
Type: SNVT_hvac_overid
Equipment functions: FH, EC/SC, RR, RR with RMF
Function
nvoManOverride_R
Type: SNVT_hvac_overid
Equipment functions: RR with RMF, TAM with RMF
Function
nvoMode
Type: SNVT_state
Equipment functions: FH, EC/SC, RR, RR with RMF
Function
nvoMode_R
Type: SNVT_state
Equipment functions: RR with RMF, TAM with RMF
Function
nvoOccCmd
Type: SNVT_occupancy
Equipment functions: FH, EC/SC, RR, RR with RMF
Function
The assigment of functional values to operating modes is stored in a table in the controller and can be configured.
The table for the assignment of functional values of SNVT_occupancy in controller or room operating modes can be adapted by means of nciConfig_Occ.
nvoOccCmd_R
Type: SNVT_occupancy
Equipment functions: RR with RMF, TAM with RMF
Function
The assigment of functional values to operating modes is stored in a table in the controller and can be configured.
The table for the assignment of SNVT_occupancy functional values to room operating modes can be adapted using the configuration parameter nciConfig_Occ.
nvoVolflowAct
Type: SNVT_flow, unit: l/s
Equipment functions: FH, EC/SC, RR, RR with RMF
Function
nvoVolflowSet
Type: SNVT_flow, unit: l/s
Equipment functions: FH, EC/SC, RR, RR with RMF
Function
nvoVolTotalExh
Type: SNVT_flow, unit: l/s
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoVolTotalSup
Type: SNVT_flow, unit: l/s
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoVelocityAct
Type: SNVT_speed_mil, unit: m/s
Equipment function: FH
Function
nvoVelocitySet
Type: SNVT_speed_mil, unit: m/s
Equipment function: FH
Function
nvoWireSensorPos
Type: SNVT_switch
Equipment function: FH
Function
nvoSwitchPos
Type: SNVT_count
Equipment function: FH
Function
nvoPressAct
Type: SNVT_press_p, unit: Pa
Equipment functions: RR with RMF, TAM with RMF
Function
nvoPressSet
Type: SNVT_press_p, unit: Pa
Equipment functions: RR with RMF, TAM with RMF
Function
nvoDampPos
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, RR with RMF
Function
nvoLocalAlarm
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoSummaryAlarm
Type: SNVT_switch
Equipment functions: RR with RMF, TAM with RMF
Function
nvoPressAlarm
Type: SNVT_switch
Equipment functions: RR with RMF, TAM with RMF
Function
nvoSystemDevices
Type: SNVT_count
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 2.0 and TCU3, TAM 3.0
Function
nvoStateDIO
Type: SNVT_state
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 2.0 and TCU3, TAM 3.0
Function
nvoSC_LockHP
Type: SNVT_switch
Function
nvoSC_GetPos
Type: SNVT_switch
Function
nvoSC_Alarm
Type: SNVT_switch
Function
nvoDO_SetByLocal
Type: SNVT_state
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 4.0
Function
nvoVoltageAI2
Type: SNVT_volt, unit V
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 4.0 and TCU3, TAM 7.0
Function
nvoVoltageAI3
Type: SNVT_volt, unit V
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 4.0 and TCU3, TAM 7.0
Function
Additional information for nvoDampMin_** and nvoDampMax_** functional values
nvoDampPosMax_** (State)
0 All damper blades in standard operating mode. Intervention is possible.
–1 All damper blades in OPEN mode (special operating mode, value = 100 %). Intervention is possible.
1 At least one damper blade in OPEN mode (special operating mode).
nvoDampPosMin_** (State)
0 All damper blades in standard operating mode. Intervention is possible.
–1 All damper blades in shut-off mode (special operating mode, value = 0 %). Intervention is not possible.
1 At least one damper blade in shut-off mode (special operating mode).
nvoDampPosMax_FH
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMin_FH
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMax_RE
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMin_RE
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMax_TE
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMin_TE
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMax_RS
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMin_RS
Type: SNVT_switch
Equipment functions: FH, EC/SC, RR, TAM, RR with RMF, TAM with RMF
Function
nvoDampPosMax_EC
Type: SNVT_switch
Equipment functions: FH, EC, SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 5.0
Function
nvoDampPosMin_EC
Type: SNVT_switch
Equipment functions: FH, EC, SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 5.0
Function
nvoDampPosMax_SC
Type: SNVT_switch
Equipment functions: FH, EC, SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 5.0
Function
nvoDampPosMin_SC
Type: SNVT_switch
Equipment functions: FH, EC, SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 5.0
Function
nvoDampPosMax_TS
Type: SNVT_switch
Equipment functions: FH, EC, SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 5.0
Function
nvoDampPosMin_TS
Type: SNVT_switch
Equipment functions: FH, EC, SC, RR, TAM, RR with RMF, TAM with RMF
from firmware version EM-LON 3.0 and TCU3, TAM 5.0
Function
OC_OCCUPIED
Standard mode | 0 | 0 | 0 | 0 |
Reduced operation | 0 | 0 | 0 | 1 |
Increased operation | 0 | 0 | 1 | 0 |
Shut-off mode | 0 | 1 | 0 | 0 |
OPEN position | 1 | 0 | 0 | 0 |
OC_UNOCCUPIED
Standard mode | 0 | 0 | 0 | 0 |
Reduced operation | 0 | 0 | 0 | 1 |
Increased operation | 0 | 0 | 1 | 0 |
Shut-off mode | 0 | 1 | 0 | 0 |
OPEN position | 1 | 0 | 0 | 0 |
OC_BYPASS
Standard mode | 0 | 0 | 0 | 0 |
Reduced operation | 0 | 0 | 0 | 1 |
Increased operation | 0 | 0 | 1 | 0 |
Shut-off mode | 0 | 1 | 0 | 0 |
OPEN position | 1 | 0 | 0 | 0 |
OC_STANDBY
Standard mode | 0 | 0 | 0 | 0 |
Reduced operation | 0 | 0 | 0 | 1 |
Increased operation | 0 | 0 | 1 | 0 |
Shut-off mode | 0 | 1 | 0 | 0 |
OPEN position | 1 | 0 | 0 | 0 |
Default values for nviManOverride
HVO_Position | Standard mode |
HVO_Close | Shut-off mode |
HVO_Open | OPEN position |
HVO_Minimum | Reduced operation |
HVO_Maximum | Increased operation |
HVO_Nul | No default |
Assignment of functional values to operating modes – basic configuration
0 | OC_OCCUPIED | Standard mode |
1 | OC_UNOCCUPIED | Reduced operation |
2 | OC_BYPASS | Increased operation |
3 | OC_BYPASS | Shut-off mode |
0xFF | OC_NUL | No default |
Default values for nviMode
4/11 | OPEN position | inactive | active |
3/12 | Shut-off mode | inactive | active |
2/13 | Increased operation | inactive | active |
1/14 | Reduced operation | inactive | active |
0/15 | Standard mode | inactive | active |
Default settings for nviManOp_Disable
– | 0 | - Manual control has been enabled on the control panel - Operating mode defaults set on DI override LON |
– | 1 | - Manual control has been disabled on the control panel - Operating mode default settings from LON have the highest priority |
Default settings for nviVolOffset_T
Percentage value | – | External volume flow rate setpoint change for temperature: 0.0 – 100.0 % |
Default settings for nviVolOffset_P
Percentage value | – | External volume flow rate setpoint change for differential pressure: 0.0 – 100.0 % |
Default settings for nviPressSetSel
0 | 0 | Differential pressure setpoint 1 |
100 | 1 | Differential pressure setpoint 2 |
Default settings for nviSunblinder
0 | 0 | Close blinds (activate switching output DO6) |
100 | 1 | Open blinds (activate switching output DO5) |
0 | -1 | No default |
Default values for nviDO_Set
7 | DO1 |
6 | DO2 |
5 | DO3 |
4 | DO4 |
3 | DO5 |
2 | DO6 |
0 inactive
1 active
nvoManOverride functional values
HVO_Position | Standard mode |
HVO_Close | Shut-off mode |
HVO_Open | OPEN position |
HVO_Minimum | Reduced operation |
HVO_Maximum | Increased operation |
nvoManOverride_R functional values
HVO_Position | Standard mode |
HVO_Close | Shut-off mode |
HVO_Open | OPEN position |
HVO_Minimum | Reduced operation |
HVO_Maximum | Increased operation |
nvoMode functional values
11 | OPEN position | inactive | active |
12 | Shut-off mode | inactive | active |
13 | Increased operation | inactive | active |
14 | Reduced operation | inactive | active |
15 | Standard mode | inactive | active |
nvoMode_R functional values
11 | OPEN position | inactive | active |
12 | Shut-off mode | inactive | active |
13 | Increased operation | inactive | active |
14 | Reduced operation | inactive | active |
15 | Standard mode | inactive | active |
nvoOccCmd functional values
0 | OC_OCCUPIED | Standard mode |
1 | OC_UNOCCUPIED | Reduced operation |
2 | OC_BYPASS | Increased operation |
3 | OC_STANDBY | Shut-off mode |
nvoOccCmd_R functional values (basic configuration)
0 | OC_OCCUPIED | Standard mode |
1 | OC_UNOCCUPIED | Reduced operation |
2 | OC_BYPASS | Increased operation |
3 | OC_STANDBY | Shut-off mode |
nvoSwitchPos functional values
1 | Switching step 1 |
2 | Switching step 2 |
3 | Switching step 3 |
0 | invalid |
nvoLocalAlarm functional values
0 | 0 | Local alarm is inactive |
100 | 1 | Local alarm is active |
nvoSummaryAlarm functional values
0 | 0 | Consolidated alarm is inactive |
100 | 1 | Consolidated alarm is active |
nvoPressAlarm functional values
0 | 0 | Room pressure alarm inactive |
100 | 1 | Room pressure alarm active |
Bit list
Switching state DO6 | 2 |
Switching state DO5 | 3 |
Switching state DO4 | 4 |
Switching state DO3 | 5 |
Switching state DO2 | 6 |
Switching state DO1 | 7 |
Switching state DI6 | 10 |
Switching state DI5 | 11 |
Switching state DI4 | 12 |
Switching state DI3 | 13 |
Switching state DI2 | 14 |
Switching state DI1 | 15 |
Default values for nvoDO_SetByLocal
7 | DO1 |
6 | DO2 |
5 | DO3 |
4 | DO4 |
3 | DO5 |
2 | DO6 |
0 inactive
1 active
nvoDampPosMax_FH functional values
Damper blade position | Additional information |
nvoDampPosMin_FH functional values
Damper blade position | Additional information |
nvoDampPosMax_RE functional values
Damper blade position | Additional information |
nvoDampPosMin_RE functional values
Damper blade position | Additional information |
nvoDampPosMax_TE functional values
Damper blade position | Additional information |
nvoDampPosMin_TE functional values
Damper blade position | Additional information |
nvoDampPosMax_RS functional values
Damper blade position | Additional information |
nvoDampPosMin_RS functional values
Damper blade position | Additional information |
nvoDampPosMax_EC functional values
Damper blade position | Additional information |
nvoDampPosMin_EC functional values
Damper blade position | Additional information |
nvoDampPosMax_SC functional values
Damper blade position | Additional information |
nvoDampPosMin_SC functional values
Damper blade position | Additional information |
nvoDampPosMax_TS functional values
Damper blade position | Additional information |
nvoDampPosMin_TS functional values
Damper blade position | Additional information |
Installation and commissioning
Installation
Commissioning
Share page
Recommend this page
Recommend this page by sending a link by mail.
Share page
Thank you for your recommendation!
Your recommendation has been sent and should arrive shortly.
Contact
We are here for you
Please specify your message and type of request.
Tel.: +971 4 3417448 | Fax: +971 4 3417449
Contact
Thank you for your message!
Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +971 4 3417448 | Fax: +971 4 3417449
Contact
We are here for you
Please specify your message and type of request.
Tel.: +971 4 3417448 | Fax: +971 4 3417449
Contact
Thank you for your message!
Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +971 4 3417448 | Fax: +971 4 3417449