img_pro_000533.png
Mini Pleat filter cells, type MFC

Eurovent_Filter_Marketing_Highlight.ai.png
Eurovent-Zertifizierung

Eurovent certification

doc_graphic_000009.png
Tested to VDI 6022

Conforms to VDI 6022

img_pro_000533.png
Eurovent_Filter_Marketing_Highlight.ai.png
doc_graphic_000009.png

MFC

For large volume flow rates and long filter life


 

Prefilters or final filters for the separation of fine dust and particulate filters for the most critical requirements in ventilation systems

  • Filter groups ISO ePM10, ISO ePM1 (fine dust filter) and EPA, HEPA (particulate filter)
  • Performance data tested in accordance with ISO 16890 or with EN 1822-1 and ISO 29463-2 to ISO 29463-5
  • Eurovent certification for fine dust filters
  • Filter media for special requirements, glass fibre papers with spacers made of thermoplastic hot-melt adhesive
  • Low initial differential pressure due to ideal pleat position and largest possible filter area
  • Compact V-design with low installation depths
  • Fitting into ducted particulate filters (types KSF, KSFS) and duct casings for particulate filters (type DCA)
  • Meets the hygiene requirements of VDI 6022

 


Introduction

Application


  • Mini Pleat filter cell type MFC for the separation of fine dust and suspended particles such as aerosols, toxic dusts, viruses and bacteria from the supply and extract air in ventilation systems with large volume flow rates and the requirement for long filter life
  • Fine dust filter: Prefilter or final filter for the separation of fine dust in ventilation systems.
  • Particulate filter: Main or final filter used for the most critical requirements of air cleanliness and sterility in areas such as industry, research, medicine, pharmaceuticals, and nuclear engineering

Special characteristics
  • Leakage test is standard for all particulate filters of classes H13, H14

Classification
  • Eurovent certification for fine dust filters

Nominal sizes

  • B × H × D [mm]

Description

Filter classes

Filter groups

  • ISO ePM10 to ISO 16890
  • ISO ePM1 to ISO 16890
  • EPA according to EN 1822
  • HEPA according to EN 1822

Filter classes

  • ePM10 70%
  • ePM1 60%
  • ePM1 90%
  • E11
  • H13
  • H14


    Options

    • Number of filter packs: 3, 5, 6, 10, 12
    • HMS: Increased filter area
    • FNU: Flat seal on the upstream side
    • FND: Flat seal on the downstream side
    • FNB: Flat seal on both sides
    • TGU: Test groove seal on the upstream side (only for filter classes H13, H14)
    • CSU: Continuous seal on the upstream side
    • CSD: Continuous seal on the downstream side
    • CSB: Continuous seal on both sides
    • WS: Without seal
    • OT: Oil mist test (only for filter classes H13, H14)
    • OTC: Oil mist test with certificate (only for filter classes H13, H14)


    Construction

    • MDF: Frame made of MDF
    • GAL: Frame made of galvanised steel
    • STA: Frame made of stainless steel


Useful additions

  • Ducted particulate filter, available as one unit (KSF, KSFS) oras a filter unit system (KSFSSP)
  • Duct casing for particulate filters (DCA)


Construction features
    • Compact V-design
    • Perimeter flat seal on the upstream side
    • Some constructions with optional foamed continuous seal or with a test groove seal (filter classes H13, H14) on the upstream side; the flat section or continuous seal can also be fitted on the downstream side or on both sides

Materials and surfaces
    • Filter media made of high-quality, moisture-resistant glass fibre papers, pleated
    • Spacers provide a uniform spacing of the pleats
    • Joint sealing compound made of permanently elastic two-component polyurethane adhesive
    • Frame made of either MDF, galvanised sheet steel, or stainless steel


Standards and guidelines
    • Test according to ISO 16890; international standard for general room air distribution; classification of arrestance efficiency based on the measured fractional arrestance efficiency, which is processed into a reporting system for the fine dust arrestance efficiency (ePM)
    • For fine dust filters, the fractional arrestance efficiency of a certain size range is determined by aerosols (DEHS and KCl)
    • The filters are classified into filter groups ISO ePM10 and ISO ePM1 depending on the tested values
    • Testing of particulate filters to EN 1822 (EPA, HEPA and ULPA filters): European standard for the testing of filtration performance in the factory, particle counting method using a liquid test aerosol
    • Uniform classification of particulate filters according to efficiency, using a test aerosol whose average particle size lies within the minimum efficiency (MPPS)
    • Particulate filters are classified according to the values determined for the local filtration efficiency and the overall filtration efficiency as EPA (filter classes E10, E11, E12), HEPA (filter classes H13, H14) or ULPA (filter classes U15, U16, U17)
    • Hygiene conformity in accordance with VDI 6022, VDI 3803,DIN 1946 Part 4, ÖNORM H 6020, SWKI VA 104-01 andSWKI 99-3 as well as EN 16798



Technical information

TECHNICAL DATA, SPECIFICATION TEXT, Order code, Related products

  • TECHNICAL DATA
  • SPECIFICATION TEXT
  • ORDER CODE

Fractional efficiency ePM10 [%] to ISO 1689070––
Fractional efficiency ePM1 [%] to ISO 16890–6090
Initial differential pressure [Pa] at nominal volume flow rate90110140
Recommended final differential pressure [Pa]450450450
Max. operating temperature [°C]808080
Maximum relative humidity [%]100100100

 

Filter class according to EN 1822E11H13H14
Efficiency [%] according to EN 1822> 95> 99.95> 99.995
Initial differential pressure [Pa] at nominal volume flow rate125250250
Recommended final differential pressure [Pa]300600600
Max. operating temperature [°C]808080
Maximum relative humidity [%]100100100



Specification text


Mini Pleat filter cells MFC for the separation of fine dust and suspended particles such as aerosols, toxic dusts, viruses and bacteria from the supply and extract air in ventilation systems. . Use as fine dust filters, i.e. as prefilters or final filters in ventilation systems; or as particulate filters, i.e. main or final filters for the most critical requirements of air cleanliness and sterility in areas such as industry, research, medicine, pharmaceuticals, and nuclear engineering. Compact depth V-design, suitable for systems with high volume flow rates and a requirement for long filter life. The filter medium is made of high-quality, moisture-resistant glass fibre papers, with spacers. Low initial differential pressure due to ideal pleat position and largest possible filter area. Mini Pleat filter cells available in market sizes, filter groups ISO ePM10, ISO ePM1 (fine dust filters) and EPA, HEPA (particulate filters). As standard, Mini Pleat filter cells are fitted with a perimeter flat seal on the upstream side. Some constructions are available with an optional foamed continuous seal on one or both sides, with a test groove seal on the upstream side. Mini Pleat filter cells used as fine dust filters are certified by Eurovent.

Special characteristics
  • Leakage test is standard for all particulate filters of classes H13, H14


Materials and surfaces
  • Filter media made of high-quality, moisture-resistant glass fibre papers, pleated
  • Spacers provide a uniform spacing of the pleats
  • Joint sealing compound made of permanently elastic two-component polyurethane adhesive
  • Frame made of either MDF, galvanised sheet steel, or stainless steel

Construction
  • MDF: Frame made of MDF
  • GAL: Frame made of galvanised steel
  • STA: Frame made of stainless steel

Sizing data
  • Filter group [ISO 16890]
  • Efficiency [%]
  • Filter class [EN 1822]
  • Volume flow rate [m³/h]
  • Initial differential pressure [Pa]
  • Nominal size [mm]

MFC – ePM1 – 90% – GAL / 610 × 610 × 292×6 / HMS / FNU / OT
|||||||||
123456789

1 Type
MFC Mini Pleat filter cell
 
2 Classification
ePM10 Fractional efficiency ePM10 to ISO 16890
ePM1 Fractional efficiency ePM1 to ISO 16890
E11 Particulate filter according to EN 1822
H13 Particulate filter according to EN 1822
H14 Particulate filter according to EN 1822
 
3 Efficiency [%]
according to ISO 16890 (not with E11, H13, H14)
 
4 Construction
MDF Frame made of MDF
GAL Frame made of galvanised steel
STA Frame made of stainless steel
 
5 Nominal size [mm]
B × H × T
 
6 Number of filter packs
3
5
6
10
12
 
7 Filter pack
No entry: standard
HMS Increased filter area
 
8 Seal
WS Without seal
FNU Flat seal on the upstream side
FND Flat seal on the downstream side
FNB Flat seal on both sides
TGU Test groove seal on the upstream side
CSU Continuous seal on the upstream side
CSD Continuous seal on the downstream side
CSB Continuous seal on both sides
 
9 Testing
No entry: no leakage test
OT Oil mist test (only for filter classes H13, H14)
OTC Oil mist test with certificate (only for filter classes H13, H14)



MFC–H13–GAL/610×610×292×10/HMS/FNU/OT
Filter class H13 particulate filter according to EN 1822
Construction frame made of galvanised steel
Nominal size 610 × 610 × 292 mm
Number of filter packs 10
Filter pack increased filter area
Seal Flat seal on the upstream side
Test oil mist test

Dimensions

  • DIMENSIONS
Dimensional drawing of MFC-…
doc_techdraw_001513.png

 

Number of filter packs: B = 305 mm : 3; B = 610 mm : 6

 

doc_techdraw_001513.png
doc_techdraw_001514.png
①②③④⑤
B [mm]H [mm]T [mm]Number of filter packsFilter classqv [l/s]qv [m³/h] ΔpA [Pa]m²kg
3056102923ePM10 70 %5902125909,27,5
6106102926ePM10 70 %118142509018,415
3056102923ePM1 60 %59021251109,27,5
6106102926ePM1 60 %1181425011018,415
3056102923ePM1 90 %59021251409,27,5
6106102926ePM1 90 %1181425014018,415
3056102923E11306110012510,17,5
3056102925E11417150012516,19
6106102926E11611220012520,215
61061029210E11833300012532,218
76261029212E111042375012538,621,6
2036102923H132428702509,77,2
3056102923H13306110025010,17,5
3056102925H13417150025016,19
6106102926H13611220025020,215
61061029210H13833300025032,218
76261029212H131042375025038,621,6
3056102925H14367132025016,19
61061029210H14733264025032,218
76261029212H14881317025038,621,6
,
①②③④⑤
B [mm]H [mm]T [mm]Number of filter packsFilter classFilter packqv [l/s]qv [m³/h]ΔpA [Pa]m²kg
3056102923ePM10 70 %5902125909,89
6106102926ePM10 70 %118142509019,515
3056102923ePM1 60 %59021251109,89
6106102926ePM1 60 %1181425011019,515
3056102923ePM1 90 %59021251409,89
6106102926ePM1 90 %1181425014019,515
3056102923E11347125012510,77,7
3056102925E11472170012517,69,2
6106102926E11694250012521,515,3
61061029210E11944340012535,118,4
76261029212E111181425012542,122,1
3056102923H1334712502509,87,4
3056102925H13472170025017,69,2
6106102926H13694250025021,515,3
61061029210H13944340025035,118,4
76261029212H131181425025042,122,1
2036102923H13HMS3201150250117,5
3056102925H13HMS556200025018,19,5
61061029210H13HMS1111400025036,219
76261029212H13HMS1389500025043,422,8
3056102925H14417150025017,69,2
61061029210H14833300025035,115,3
76261029212H141000360025042,122,1

Downloads

product information

  • Print page MFC

  • Product Data Sheet Mini Pleat Filters, Type MFC

    Product Data Sheet 2,4 MB pdf

certificates

  • Non-CE Manufacturer's statement MFC

    MFC_NotCE_2022_02_08_13_40_08_DE_en Certificate 2,5 MB pdf

TROX Services

production {"X-Frame-Options"=>"SAMEORIGIN", "X-XSS-Protection"=>"1; mode=block", "X-Content-Type-Options"=>"nosniff", "X-Download-Options"=>"noopen", "X-Permitted-Cross-Domain-Policies"=>"none", "Referrer-Policy"=>"strict-origin-when-cross-origin", "Content-Security-Policy"=>"frame-ancestors 'self' https://*.scrivito.com https://punchoutcommerce.com https://www.trox.de https://trox-extern.com https://*.onventis.com http://localhost:63342 http://cerebrum.local https://trox4u.troxgroup.com", "Strict-Transport-Security"=>"max-age=31536000; includeSubDomains", "Content-Type"=>"text/html; charset=utf-8"}

Share page

Recommend this page

Recommend this page by sending a link by mail.

Fields marked with an (*) are required fields.

Share page

Thank you for your recommendation!

Your recommendation has been sent and should arrive shortly.

Contact

We are here for you

Please specify your message and type of request.
Tel.: +971 4 3417448 | Fax: +971 4 3417449

Attachment (max. 10MB)
Your message
Your message to

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +971 4 3417448 | Fax: +971 4 3417449

Contact

We are here for you

Please specify your message and type of request.
Tel.: +971 4 3417448 | Fax: +971 4 3417449

Attachment (max. 10MB)
Your message
Your message to

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +971 4 3417448 | Fax: +971 4 3417449

TROX Logo
By clicking the button, you allow us to provide you with an excellent website experience and easy shopping processes. These cookies include ones that are necessary for the operation of the site and for the control of our services and applications, as well as ones that are used solely for statistical purposes, for convenience settings or to display personalized content. You can decide which categories you want to allow and you can adjust the data utilisation settings based on your individual requirements. Please note that, depending on the settings that you have selected, all functionalities of the page might not be available. You can change your selection at any time.
Cookie settings